Listing Program At89s51
This is a Low Cost Development Board that can be used to quickly evaluate and demonstrate the capabilities of Atmel AT89S52 / AT89C51 / AT89S51 / AT89C52 microcontrollers. The board is designed to work as a header providing access to all pins for external connections, ideally suitable for quick start development purposes. Listing Program At89s51.
Water level controller using 8051.
A water level controller using 8051 is shown in this article. A lot of water level controller projects have been published in this website but this is the first one based on a microcontroller. This water level controller monitors the level of the over head tank  and automatically switches on the water pump when ever the level goes below a preset limit. The level of the over head tank is indicated using 5 LED’s and the pump is switched OFF when the over head tank is full. The pump is not allowed to start if the water level in the sump tank is low and also the pump is switched OFF when the level inside the sump tank goes low during a pumping cycle.
We are selling a Project Kit for this Water Level Controller which can be bought from our Online Store. The project kit is a modified version of the project shown above. This Water Level Controller project kit uses 4 float switches to measure water level. The status of water level in the tank and status of the motor is displayed using an LCD module. This system monitors the water level of the tank and automatically switches ON the motor whenever tank is empty. The motor is switched OFF when the overhead tank or container is FULL.
The Complete Book of Running [James Fixx] on Amazon.com. *FREE* shipping on qualifying offers. Discusses not only the physical benefits of running, but its psychological benefits as well: increasing self-esteem. The complete book of running fixx pdf converter. The Complete Book of Running has 392 ratings and 43 reviews. Loederkoningin said: A deliciously outdated book. Fixx wrote The Complete Book of Running in.
Listing Program Mikrokontroler At89s51
The use of float switches makes the circuit rugged and ensures a maintenance free operation over a very long period of time. The project kit is available in plug and play form and do it yourself form. A 12-0-12 mains transformer is also available with the kit and it is not shown in the figure below.
Main article continues…………….
The level sensor probes for the overhead tank are interfaced to the port 2 of the microcontroller through transistors. Have a look at the sensor probe arrangement for the overhead tank in Fig1. A positive voltage supply probe goes to the down bottom of the tank. The probes for sensing 1/4, 1/2, 3/4 and FULL levels are placed with equal spacing one by one above the bottom positive probe. Consider the topmost (full level) probe, its other end is connected to the base of transistor Q4 through resistor R16. Whenever water rises to the full level current flows into the base of transistor Q4 which makes it ON and so its collector voltage goes low. The collector of Q4 is connected to P2.4 and a low voltage at  P2.4 means the over head tank is not FULL. When water level goes below the full level probe, the base of Q2 becomes open making it OFF. Now its collector voltage goes high and high at P2.4 means the tank is not full. The same applies to other sensor probes (3/4, 1/2, 1/4) and the microprocessor understands the current level by scanning the port pins P2.4 ,P2.5, P2.6 and P2.7. All these port pin are high (all sensor probes are open) means the tank is empty.
Port pin P0.5 is used to control the pump. When ever it is required start pumping, the controller makes P0.5 low which makes transistor Q6 ON which in turn activates the relay K1 that switches the pump. Also the LED d6 glows indicating the motor is ON. LED D7 is the low sump indicator. When the water level in the sump tank goes low, the controller makes P0.7 low which makes LED D7 to glow. The circuit diagram of the water level controller is shown in the figure below.
Circuit diagram.
Program.
MOV P2,#11111111B // initiates P2 as sensor input
MOV P0,#11111111B // initiates P2 as the output port
MOV A,#00000000B
MAIN:ACALL SMPCK // checks the level of the sump tank
MOV A,P2 // moves the current status of P2 to A
CJNE A,#11110000B,LABEL1 // checks whether tank is full
SETB P0.1
SETB P0.2
SETB P0.3
SETB P0.4
CLR P0.0 // glows full level LED
SETB P0.5
LABEL1:MOV A,P2
CJNE A,#11111000B,LABEL2 // checks whether tank is 3/4
SETB P0.0
SETB P0.2
SETB P0.3
SETB P0.4
CLR P0.1 // glows 3/4 level LED
LABEL2:MOV A,P2
CJNE A,#11111100B,LABEL3 // checks whether tank is 1/2
SETB P0.0
SETB P0.1
SETB P0.3
SETB P0.4
CLR P0.2 // glows 1/2 level LED
LABEL3:MOV A,P2
CJNE A,#11111110B,LABEL4 // checks whether tank is 1/4
SETB P0.0
SETB P0.1
SETB P0.2
SETB P0.4
CLR P0.3 // glows 1/4 level LED
JB P0.6,LABEL4
CLR P0.5 // switches motor ON
LABEL4:MOV A,P2
CJNE A,#11111111B,MAIN // checks whether tank is empty
SETB P0.0
SETB P0.1
SETB P0.2
SETB P0.3
CLR P0.4 // glows EMPTY LED
JB P0.6,MAIN // checks whether sump is low
CLR P0.5 // switches motor ON
SJMP MAIN
SMPCK:JB P0.6,LABEL5 // checks whether sump is low
SETB P0.7 // extinguishes the sump low indicator LED
SJMP LABEL6
LABEL5:SETB P0.5 // switches the pump OFF
CLR P0.7 // glows sump low indicator LED
LABEL6:RET
END
Related Projects
Moisture Sensing Automatic Plant Watering System – is an interesting project for hobbyists and students alike. This project is designed as a DIY automatic plant watering system based on soil moisture. Soil moisture is sensed using YL69 moisture sensor and 8051 microcontroller is used to interpret the sensor data and turn ON/OFF a motor pump for watering.